Results 1 to 10 of 72

Thread: Upgrade PSJailbreak Dongle Clone *EASY WAY* *TUT*


  1. Join Date Aug 2010

    Posts 698

    Membership Banned

    Reputation: 1051

    11-30-2010 11:52 PM #1 Upgrade+Jailbreak /w PSJailbreak Dongle Clone *EASY WAY* *TUT*

    How To Upgrade Your PS Jailbreak Clone Dongle
    *THE EASY WAY!*



    This tutorial is for updating the dongle ONLY, please view my other post on Jailbreaking 3.50 (:


    For Users Who Have A Problem With Their Computer Not Recongnizing The Dongle..
    Quote Originally Posted by galanoth View Post
    i found a solution for when your pc doesnt see the JB clone
    it here: [Only registered and activated users can see links. ]
    post #26 hope it helps for some of you who have the same problem as is did
    BIG thanks to galanoth, saved me some time



    WHEN FINISHED READ NOTE AT BOTTOM OF TUTORIAL FOR AN IMPORTANT STEP ON AVOIDING THE "Verify fail at 0x00CBC" OR ANY OTHER VERIFY FAIL CODES!


    BEFORE YOU EVEN START PLEASE TAKE A LOOK AT THIS!
    THIS IS THE JAILBREAK CHIP YOU WILL NEED IN ORDER FOR THIS TO WORK!



    NOTE: THE SLIT IN THE CHIP WERE THE LIGHTS ARE!

    Files you'll need:

    • [Only registered and activated users can see links. ]
    • [Only registered and activated users can see links. ]

    (Use the AT90USBKEY file, not AT90USBKEY2 or any other file or this wont work..Ignore instructions too, thats an old tut for BlackCat boards.)




    Upgrade Instruction:
    *MAKE SURE YOU HAVE DOWNLOADED NEEDED FILES*

    1.) [Only registered and activated users can see links. ]


    2.) When installed,go to installation folder, namely Atmel\Flip 3.4.2\usb\, find libusb0.dll and libusb0_x64.dll, copy them to folder Flip 3.4.2\bin


    3.) Then plug PSjailbreak into USB port in PC, the red green light will light up.


    4.) Meanwhile PC reminds you that unusable unkown device found.


    5.) Ignore it, wait for a few seconds, new hardware AT90USB162 DFU will be found, pc asks you to provide driver,





    6.) choose USB folder in Flip as the Install Path, for example Atmel\Flip 3.4.2\usb\





    7.) then the installation begins.





    8.) When the driver is installed, we can write on AT90USB162.





    9.) Run Flip, go to Device -> Select..., and choose AT90USB162





    10.) Then go to File -> Load HEX File...





    11.) Choose the HEX file you want to write into, (Choose one of the files provided at the top of the post)


    Attention: HEX must be put in the English path so that it can be read


    12.) Then you can see HEX file parsed shown in the left bottom.





    13.) Then go to Settings -> Communication ->USB, choose OPEN USB port.





    14.) Then the chip is open and ready to be written.





    15.) Check HEX File, make sure if it’s the right HEX that you want to write into.

    IF YOU GET THE VERIFY FAILED ERROR , CLICK THE "READ TARGET DEVICE MEMORY" TO READ THE CHIP , DO THIS 3-4 TIMES THEN CLICK RUN AGAIN!


    16.) Choose RUN in the left bottom, then the chip is being written. It will be done in a few seconds. You will see Verify PASS in the left bottom when it’s finished.





    Now the chip has been written. Turn off Flip and unplug the PS jailbreak dongle out of PC.


    Kudos to myself for finding a fix for the "Verify Failed Error" (:


    Good Luck, Have Fun (:
    SOTK
    Last edited by sMoKiNyOo; 12-14-2010 at 01:00 PM.

  2. CRaZyY Banned

    Join Date May 2010

    Posts 2,121

    Membership Banned

    Reputation: 789

    12-01-2010 12:16 AM #2

    Quote Originally Posted by SOTK77 View Post
    How To Upgrade Your PS Jailbreak Clone Dongle
    *THE EASY WAY!*




    Files you'll need:

    • [Only registered and activated users can see links. ]


    • Any of these .HEX files


    • [Only registered and activated users can see links. ]
    • [Only registered and activated users can see links. ]
    • [Only registered and activated users can see links. ]
    • [Only registered and activated users can see links. ]
    • [Only registered and activated users can see links. ]
    • [Only registered and activated users can see links. ]
    • [Only registered and activated users can see links. ]


    • Wanna use your own file? Go ahead!



    Upgrade Instruction:
    *MAKE SURE YOU HAVE DOWNLOADED NEEDED FILES*

    1.) [Only registered and activated users can see links. ]


    2.) When installed,go to installation folder, namely Atmel\Flip 3.4.2\usb\, find libusb0.dll and libusb0_x64.dll, copy them to folder Flip 3.4.2\bin


    3.) Then plug PSjailbreak into USB port in PC, the red green light will light up.


    4.) Meanwhile PC reminds you that unusable unkown device found.


    5.) Ignore it, wait for a few seconds, new hardware AT90USB162 DFU will be found, pc asks you to provide driver,





    6.) choose USB folder in Flip as the Install Path, for example Atmel\Flip 3.4.2\usb\





    7.) then the installation begins.





    8.) When the driver is installed, we can write on AT90USB162.





    9.) Run Flip, go to Device -> Select..., and choose AT90USB162





    10.) Then go to File -> Load HEX File...





    11.) Choose the HEX file you want to write into, (Choose one of the files provided at the top of the post)


    Attention: HEX must be put in the English path so that it can be read


    12.) Then you can see HEX file parsed shown in the left bottom.





    13.) Then go to Settings -> Communication ->USB, choose OPEN USB port.





    14.) Then the chip is open and ready to be written.





    15.) Check HEX File, make sure if it’s the right HEX that you want to write into.



    16.) Choose RUN in the left bottom, then the chip is being written. It will be done in a few seconds. You will see Verify PASS in the left bottom when it’s finished.





    Now the chip has been written. Turn off Flip and unplug the PS jailbreak dongle out of PC.



    SOURCE: [Only registered and activated users can see links. ]

    Good Luck, Have Fun (:
    SOTK
    i have the clone ps jailbreak thingy...does this mean i can downgrade my ps3 now?

    ---------- Post added at 01:16 AM ---------- Previous post was at 01:04 AM ----------

    so can you lol im really interested!

  3. Join Date Aug 2010

    Posts 698

    Membership Banned

    Reputation: 1051

    12-01-2010 12:19 AM #3

    Not necessarily, This is the way you would Upgrade and flash the Dongle, but ive yet to find a working .Hex file for 3.50

    HIGHLY possible in the near future!

  4. Join Date Sep 2010

    Posts 359

    Membership Standard

    Reputation: 1024

    12-01-2010 12:35 AM #4

    Is it possible to make a PS clone?

    This Equals ...


  5. Join Date Aug 2010

    Posts 698

    Membership Banned

    Reputation: 1051

    12-01-2010 01:03 AM #5

    PS Jailbreak clones are Non-official jailbreaks, sold from ie psjailbreakstore.com ect.

  6. Join Date Dec 2010

    Posts 2

    Membership Standard

    Reputation: 10

    12-01-2010 02:59 AM #6 PSFreedom Payload

    does this mean that I can upgrade/flash my clone dongle with a PSFreedom Payload or psgroove?

  7. Join Date Aug 2010

    Posts 698

    Membership Banned

    Reputation: 1051

    12-01-2010 12:26 PM #7

    Yes, you just need to find the correct HEX file that works with 3.50..Ive been looking, hope to find one soon!

    PS if you find a working one please send me the file so I can update this post.

  8. Join Date Oct 2010

    Posts 66

    Membership Banned

    Reputation: 278

    12-01-2010 12:29 PM #8

    Can Someone Please Test This, & Nice Thread, Thumbs Up :y:

  9. Join Date Aug 2010

    Posts 698

    Membership Banned

    Reputation: 1051

    12-01-2010 12:31 PM #9

    Yes, agreed someone please test, I can get the HEX files to sucessfully flash to the chip, but I need to find a working HEX to jailbreak 3.50, or downgrade whichever.

  10. Hawkin's Avatar

    Hawkin Lord of the Undead

    Join Date Jun 2010

    Posts 723

    Membership Donator

    Reputation: 11546

    12-01-2010 12:38 PM #10

    Quote Originally Posted by SOTK77 View Post
    3.) Then plug PSjailbreak into USB port in PC, the red green light will light up.
    4.) Meanwhile PC reminds you that unusable unkown device found.
    5.) Ignore it, wait for a few seconds, new hardware AT90USB162 DFU will be found, pc asks you to provide driver,
    6.) choose USB folder in Flip as the Install Path, for example Atmel\Flip 3.4.2\usb\
    7.) then the installation begins.
    8.) When the driver is installed, we can write on AT90USB162.
    This doesn't work for all of the JB demos/clones. From what I have found on the web My JB and most of the clones, have a different Product and Vendor ID then the Flip driver has. (xAAAA xCCCC)
    So it installs as a Generic USB Hub that won't start.
    Last edited by Hawkin; 12-01-2010 at 12:42 PM.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •