(adsbygoogle = window.adsbygoogle || []).push({});

• You must login or register to view this content.
  
• You must login or register to view this content.
  

(Use the AT90USBKEY file, not AT90USBKEY2 or any other file or this wont work..Ignore instructions too, thats an old tut for BlackCat boards.)

1.) You must login or register to view this content.


2.) When installed，go to installation folder, namely Atmel\Flip 3.4.2\usb\, find libusb0.dll and libusb0_x64.dll, copy them to folder Flip 3.4.2\bin


3.) Then plug PSjailbreak into USB port in PC, the red green light will light up.


4.) Meanwhile PC reminds you that unusable unkown device found.


5.) Ignore it, wait for a few seconds, new hardware AT90USB162 DFU will be found, pc asks you to provide driver,


You must login or register to view this content.


6.) choose USB folder in Flip as the Install Path, for example Atmel\Flip 3.4.2\usb\


You must login or register to view this content.


7.) then the installation begins.


You must login or register to view this content.


8.) When the driver is installed, we can write on AT90USB162.


You must login or register to view this content.


9.) Run Flip, go to Device -> Select..., and choose AT90USB162


You must login or register to view this content.


10.) Then go to File -> Load HEX File...


You must login or register to view this content.


11.) Choose the HEX file you want to write into, (Choose one of the files provided at the top of the post)


Attention: HEX must be put in the English path so that it can be read


12.) Then you can see HEX file parsed shown in the left bottom.


You must login or register to view this content.


13.) Then go to Settings -> Communication ->USB, choose OPEN USB port.


You must login or register to view this content.


14.) Then the chip is open and ready to be written.


You must login or register to view this content.


15.) Check HEX File, make sure if it’s the right HEX that you want to write into.

Originally posted by another user

IF YOU GET THE VERIFY FAILED ERROR , CLICK THE "READ TARGET DEVICE MEMORY" TO READ THE CHIP , DO THIS 3-4 TIMES THEN CLICK RUN AGAIN!

16.) Choose RUN in the left bottom, then the chip is being written. It will be done in a few seconds. You will see Verify PASS in the left bottom when it’s finished.


You must login or register to view this content.


Now the chip has been written. Turn off Flip and unplug the PS jailbreak dongle out of PC.





Good Luck, Have Fun
SOTK

i found a solution for when your pc doesnt see the JB clone
it here: You must login or register to view this content.
post #26 hope it helps for some of you who have the same problem as is did

Thanks bro, added into tut

Hi, i've bought this clone: You must login or register to view this content. do you think i can do this? And where did you bought your clone? thanks.

Your in luck, thats the proper dongle :y:

also, bought mine at Ps3JailbreakStore.com

Ok, thanks it all worked but I got one problem:

at the end i cat the verify failed error. Then I do the thing over again. But then the program thing fails. If i put the program thing away, the verify pass. Is it a problem that the program fails? Cuz the verify pass.

If you read my tutorial you would have found the fix to this error.. You can fix this by pressing Read Device 2-3 times before you click run.


-SOTK

whats the point of this?? you can't downgrade with it soo?

The main point is how to upgrade the clone dongle.. If you find the appropriate HEX file then you CAN downgrade 3.50 and or Jailbreak 3.41.

---------- Post added at 12:53 PM ---------- Previous post was at 12:51 PM ----------



That method hasnt been confirmed yet, The minute its confirmed this post will be updated.

Also, thats the same site I bought my Dongle, I have confirmed at it jailbreaks 3.41, and other sites have confirmed it Jailbreaks 3.50 with PSGrade. I do encourage testing this method though.

SOTK